i-8 for complete specifications and additional models: u.s. www.omron.com/oei canada www.omron.ca smartstep servos cost-effective servo capability with stepper simplicity easily migrate from steppers to the higher precision of servos in minutes with omron's smartstep servo drivers and ultra- compact 3-phase servo motors. they accept pulse-train input that can be configured quickly via simple dip switches and have an on-line auto-tuning function. smartstep offers all the simplicity and cost-effectiveness of a stepper with the added advantages of the servo drive capability. motor features ? sizes 30 w to 750 w, rated speed 3,000 rpm accepts incremental encoder input at 2,000 p/r cylindrical and flat type servo motors available peak torque up to three times continuous torque during 3 seconds easy to install with pre-built cables motors with brake are available driver features output range from 30 w to 750 w 300% peak current over nominal control via pulse train (speed and position) four position resolution settings: 500 pulses/rotation (0.72 /step) 1,000 pulses/rotation (0.36 /step) 5,000 pulses/rotation (0.072 /step) 10,000 pulses/rotation (0.036 /step) smartstep does not require the use of pc configuration software, making setup as easy as using a stepper motor for basic capab ilities to optimize performance, use pc software for on-line auto- tuning of values and monitoring ordering information add cable length to the part number in place of @@@ : 003 for 3 m cable, 005 for 5 m, 010 for 10 m, 015 for 15 m and 020 for 20 m. servos smartstep k091 smartstep servo drive smartstep servo motor computer monitor software for windows servo relay unit connector terminal block position control module (with pulse output) position control module, customizable counter module, or devicenet one-axis analog monitor cable
for complete specifications and additional models: u.s. www.omron.com/oei canada www.omron.ca i-9 smartstep servos note: circled numbers refer to the configuration diagram on page i-8. smartstep servos wattage servo motor model servo drive model a power cable/encoder cable model (add cable length for @@@ ) cylindrical servo motors 100 vac without brake, shaft without keyway 30 w r7m-a03030-s1 r7d-apa3l r7a-cea @@@ s 50 w r7m-a05030-s1 r7d-apa5l r7a-cea @@@ s 100 w r7m-a10030-s1 r7d-ap01l r7a-cea @@@ s 200 w r7m-a20030-s1 r7d-ap02l r7a-cea @@@ s 400 w r7m-a40030-s1 r7d-ap04l r7a-cea @@@ s cylindrical servo motors 100 vac with brake, shaft with keyway 30 w r7m-a03030-bs1 r7d-apa3l r7a-cea @@@ b 50 w r7m-a05030-bs1 r7d-apa5l r7a-cea @@@ b 100 w r7m-a10030-bs1 r7d-ap01l r7a-cea @@@ b 200 w r7m-a20030-bs1 r7d-ap02l r7a-cea @@@ b 400 w r7m-a40030-bs1 r7d-ap04l r7a-cea @@@ b cylindrical servo motors 200 vac without brake, shaft with keyway 30 w r7m-a03030-s1 r7d-apa3h r7a-cea @@@ s 50 w r7m-a05030-s1 r7d-apa5h r7a-cea @@@ s 100 w r7m-a10030-s1 r7d-ap01h r7a-cea @@@ s 200 w r7m-a20030-s1 r7d-ap02h r7a-cea @@@ s 400 w r7m-a40030-s1 r7d-ap04h r7a-cea @@@ s 750 w r7m-a75030-s1 r7d-ap08h r7a-cea @@@ s cylindrical servo motors 200 vac with brake, shaft with keyway 30 w r7m-a03030-bs1 r7d-apa3h r7a-cea @@@ b 50 w r7m-a05030-bs1 r7d-apa5h r7a-cea @@@ b 100 w r7m-a10030-bs1 r7d-ap01h r7a-cea @@@ b 200 w r7m-a20030-bs1 r7d-ap02h r7a-cea @@@ b 400 w r7m-a40030-bs1 r7d-ap04h r7a-cea @@@ b 750 w r7m-a75030-bs1 r7d-ap08h r7a-cea @@@ b flat servo motors 100 vac without brake, shaft with keyway 100 w r7m-ap10030-s1 r7d-ap01l r7a-cea @@@ s 200 w r7m-ap20030-s1 r7d-ap02l r7a-cea @@@ s 400 w r7m-ap40030-s1 r7d-ap04l r7a-cea @@@ s flat servo motors 100 vac with brake, shaft with keyway 100 w r7m-ap10030-bs1 r7d-ap01l r7a-cea @@@ b 200 w r7m-ap20030-bs1 r7d-ap02l r7a-cea @@@ b 400 w r7m-ap40030-bs1 r7d-ap04l r7a-cea @@@ b flat servo motors 200 vac without brake, shaft with keyway 100 w r7m-ap10030-s1 r7d-ap01h r7a-cea @@@ s 200 w r7m-ap20030-s1 r7d-ap02h r7a-cea @@@ s 400 w r7m-ap40030-s1 r7d-ap04h r7a-cea @@@ s 750 w r7m-ap75030-s1 r7d-ap08h r7a-cea @@@ s flat servo motors 200 vac with brake, shaft with keyway 100 w r7m-ap10030-bs1 r7d-ap01h r7a-cea @@@ b 200 w r7m-ap20030-bs1 r7d-ap02h r7a-cea @@@ b 400 w r7m-ap40030-bs1 r7d-ap04h r7a-cea @@@ b 750 w r7m-ap75030-bs1 r7d-ap08h r7a-cea @@@ b
i-10 for complete specifications and additional models: u.s. www.omron.com/oei canada www.omron.ca smartstep servos cables and accessories description devices connected specification model b servo relay units connect cables from plc position controller and servo drive cs1w-nc113/133, cj1w-nc113/133; 1 axis; does not support communications functions ? xw2b-20j6-1b cs1w-nc213/233/413/433, cj1w-nc213/233/413/433; 2 axes; does not support communications functions ? xw2b-40j6-2b cqm1h-plb21 and cqm1-cpu43-v1; 1 axis; does not support communications functions ? xw2b-20j6-3b cs1w-nc213/233/413/433, cj1w-nc213/233/ 413/433; 2 axes; supports communications functions ? xw2b-40j6-4a cj1m-cpu22/23; 1 axis; does not support communications functions ? xw2b-20j6-8a cj1m-cpu22/23; 2 axes; does not support communications functions ? xw2b-40j6-9a c universal terminal block cable to servo drive doesn?t support communications functions. (for the xw2b- @@ j6- @ b) 1 m length xw2z-100j-b5 2 m length xw2z-200j-b5 d position controller plc module cable cqm1h-plb21 and cqm1-cpu43-v1 to xw2b-20j6-3b servo relay unit 1 m length xw2z-100j-a3 cj1w-nc113 to xw2b-20j6-1b servo relay unit 1 m length xw2z-100j-a16 cj1w-nc213 or cj1w-nc413 to xw2b-20j6-2b servo relay unit 1 m length xw2z-100j-a17 cj1w-nc133 to xw2b-20j6-1b servo relay unit 1 m length xw2z-100j-a20 cj1w-nc233 or cj1w-nc433 to xw2b-40j6-2b servo relay unit 1 m length xw2z-100j-a21 cj1m-cpu22 or cj1m-cpu23 to xw2b-20j6-8a (1 axis) or xw2b-40j6-9a (2 axes) servo relay unit 1 m length xw2z-100j-a26 cs1w-nc113 to xw2b-20j6-1b servo relay unit 1 m length xw2z-100j-a8 cs1w-nc213 or cs1w-nc413 to xw2b-40j6-2b servo relay unit 1 m length xw2z-100j-a9 cs1w-nc133 to xw2b-20j6-b1 servo relay unit 1 m length xw2z-100j-a12 cs1w-nc233 or cs1w-nc433 to xw2b-40j6-2b servo relay unit 1 m length xw2z-100j-a13 e control cable for general-purpose controllers (mating connector for cj1 on one end, open ended on the other end) 1 m length R88A-CPU001S 2 m length r88a-cpu002s f universal terminal block for position control modules with pulse output and general-purpose controllers ? xw2b-40f5-p connector cable between terminal block and servo driver 1 m length r88a-ctu001n 2 m length r88a-ctu002n g analog monitor cable (port cn4) servo drive to pc 1 m length r88a-cmw001s h computer monitor cable (port cn3) servo drive to pc 2 m length r7a-cca002p2 filters for servo drive r7d-apa3h, apa5h, ap01h, ap02h; r7d-apa3l, apa5l, ap01l, ap02l 4 a, 250 vac single phase r88a-fiw104-e for servo drive r7d-ap04h, ap04l 7 a, 250 vac single phase r88a-fiw107-e for servo drive r7d-ap08h 15 a, 250 vac single phase r88a-fiw115-e control i/o connector (cn1) ? ? r88a-cnu01c smartstep encoder connector (cn2) ? ? r7a-cna01r external regeneration resistor ? 200 w, 47 ? r88a-rr22047s parameter copy unit with cable ? ? r7a-pr02a configuration and monitoring software for servo drives and inverters version 1.11 or higher cx-drive complete omron software suite includes cx-drive ? cx-one
for complete specifications and additional models: u.s. www.omron.com/oei canada www.omron.ca i-11 smartstep servos specifications servo drives general specifications servo drives performance specifications 100 vac input models 200 vac input models item specification operating ambient 0 to 55 c (32 f to 131 f), 90% rh max. (with no condensation) storage ambient -20 to 85 c (-4 f to 185 f), 90% rh max. (with no condensation) storage/operating atmosphere no corrosive gases. vibration resistance 10 to 55 hz in x, y, and z directions with 0.1-mm double amplitude or acceleration of 4.9 m/s 2 max., whichever is smaller impact resistance acceleration 19.6 m/s 2 max., in x, y, and z directions, three times insulation resistance between power line terminals and case: 0.5 m ? min. (at 500 vdc) dielectric strength between power line terminals and case: 1,500 vac for 1 min. at 50/60 hz between each control signal and case: 500 vac for 1 min. protective structure built into panel (ip10). international standards approval obtained for ul, cul, and en (emc directive and low-voltage directive) item specification model r7d-apa3l r7d-apa5l r7d-ap01l r7d-ap02l r7d-ap04l rated output 30 w 50 w 100 w 200 w 400 w continuous output current (rms) 0.42 0.6 0.89 2.0 2.6 momentary maximum output current (rms) 1.3 1.9 2.8 6.0 8.0 control power supply single-phase 100/115 vac (85 to 127 v) 50/60 hz main-circuit power supply single-phase 100/115 vac (85 to 127 v) 50/60 hz (voltage doubler method) control method all-digital servo speed feedback 2,000 pulses/revolution incremental encoder inverter method pwm method based on igbt pwm frequency 11.7 khz weight [kg (lb)] 0.8 (1.76) 0.8 (1.76) 0.8 (1.76) 0.8 (1.76) 1.1 (2.43) compatible motor voltage 200 v compatible motor capacity 30 w 50 w 100 w 200 w 400 w command pulse response 250 khz applicable servo motor (r7m-) a03030_ a05030_ a10030_ a20030_ a40030_ ? ? ap10030_ ap20030_ ap40030_ item specification model r7d-apa3h r7d-apa5h r7d-ap01h r7d-ap02h r7d-ap04h r7d-ap08h rated output 30 w 50 w 100 w 200 w 400 w 750 w continuous output current (rms) 0.42 0.6 0.89 2.0 2.6 4.4 momentary maximum output current (rms) 1.3 1.9 2.8 6.0 8.0 13.9 control power supply single-phase 200/230 vac (170 to 253 v) 50/60 hz main-circuit power supply single-phase 200/230 vac (170 to 253 v) 50/60 hz (three-phase 200/230 vac can be used with the 750 w model) control method all-digital servo speed feedback 2,000 pulses/revolution incremental encoder inverter method pwm method based on igbt pwm frequency 11.7 khz weight [kg (lb)] 0.8 (1.76) 0.8 (1.76) 0.8 (1.76) 0.8 (1.76) 1.1 (2.43) 1.7 (3.75) servo motor voltage 200 v servo motor capacity 30 w 50 w 100 w 200 w 400 w 750 w command pulse response 250 khz applicable servo motor (r7m-) a03030 a05030 a10030 a20030 a40030 a75030 ? ? ap10030 ap20030 ap40030 ap75030
i-12 for complete specifications and additional models: u.s. www.omron.com/oei canada www.omron.ca smartstep servos servo motor general specifications servo motor performance specifications flat servo motors without brakes flat servo motors with brakes item specification operating ambient 0 c to 40 c (32 f to 104 f), 20% to 80% rh (with no condensation) storage ambient -20 c to 60 c (-4 f to 140 f), 20% to 80% rh (with no condensation) storage/operating atmosphere no corrosive gases vibration resistance 10 to 2,500 hz in x, y, and z directions with 0.2 mm double amplitude or acceleration of 24.5 m/s 2 max., whichever is smaller impact resistance acceleration 98 m/s 2 max., in a vertical direction, two times insulation resistance between power line terminals and fg: 10 m ? min. (at 500 vdc) dielectric strength between power line terminals and fg: 1,500 v ac for 1 min at 50/60 hz run position any direction insulation grade ty p e b structure totally-enclosed self-cooling protective structure ip55 for both the cylindrical and flat servo motors vibration grade v-15 mounting method flange-mounting international standards approval obtained for ul, cul, and en (emc directive and low-voltage directive) item r7m-ap10030-s1 r7m-ap20030-s1 r7m-ap40030-s1 r7m-ap75030-s1 rated output 100 w 200 w 400 w 750 w rated torque 0.318 nm 0.637 nm 1.27 nm 2.39 nm rated rotation speed 3,000 r/min. 3,000 r/min. 3,000 r/min. 3,000 r/min. momentary maximum rotation speed 4,500 r/min. 4,500 r/min. 4,500 r/min. 4,500 r/min. momentary maximum torque 0.96 nm 1.91 nm 3.82 nm 7.1 nm rated current 0.89 a (rms) 2.0 a (rms) 2.6 a (rms) 4.1 a (rms) momentary maximum current 2.8 a (rms) 6.0 a (rms) 8.0 a (rms) 13.9 a (rms) rotor inertia 6.5 10 -6 kgm 2 2.09 10 -5 kgm 2 3.47 10 -5 kgm 2 2.11 10 -4 kgm 2 power rate 15.7 kw/s 19.4 kw/s 46.8 kw/s 26.9 kw/s allowable radial load 78 n 245 n 245 n 392 n allowable thrust load 49 n 68 n 68 n 147 n weight (without brake -s1) 0.7 kg 1.4 kg 2.1 kg 4.2 kg applicable servo driver r7d-ap01h/l r7d-ap02h/l r7d-ap04h/l r7d-ap08h encoder resolution 2,000 pulses/revolution for phase-a and phase-b, 1 pulse/revolution for phase-z radiation shield dimensions t6 250 mm square t12 300 mm square item r7m-ap10030-bs1 r7m-ap20030-bs1 r7m-ap40030-bs1 r7m-ap75030-bs1 rated output 100 w 200 w 400 w 750 w rated torque 0.318 nm 0.637 nm 1.27 nm 2.39 nm rated rotation speed 3,000 r/min. 3,000 r/min. 3,000 r/min. 3,000 r/min. momentary maximum rotation speed 4,500 r/min. 4,500 r/min. 4,500 r/min. 4,500 r/min. momentary maximum torque 0.96 nm 1.91 nm 3.82 nm 7.1 nm rated current 0.89 a (rms) 2.0 a (rms) 2.6 a (rms) 4.1 a (rms) momentary maximum current 2.8 a (rms) 6.0 a (rms) 8.0 a (rms) 13.9 a (rms) rotor inertia 6.5 10 -6 kgm 2 2.09 10 -5 kgm 2 3.47 10 -5 kgm 2 2.11 10 -4 kgm 2 power rate 15.7 kw/s 19.4 kw/s 46.8 kw/s 26.9 kw/s allowable radial load 78 n 245 n 245 n 392 n allowable thrust load 49 n 68 n 68 n 147 n weight (with brake -bs1) 0.9 kg 1.9 kg 2.6 kg 5.7 kg applicable servo driver r7d-ap01h/l r7d-ap02h/l r7d-ap04h/l r7d-ap08h encoder resolution 2,000 pulses/revolution for phase-a and phase-b, 1 pulse/revolution for phase-z radiation shield dimensions t6 250 mm square t12 300 mm square brake specifications brake inertia 3.1 10 -6 kgm 2 1.52 10 -5 kgm 2 1.52 10 -5 kgm 2 8.75 10 -5 kgm 2 excitation voltage 24 v dc 10% power consumption (at 20 c) 6 w 5 w 7.6 w 7.5 w current consumption (at 20 c) 0.25 a 0.21 a 0.32 a 0.31 a static friction torque 0.4 nm min. 0.9 nm min. 1.9 nm min. 3.5 nm min. attraction time 40 ms max. 40 ms max. 40 ms max. 40 ms max. release time 20 ms max. 20 ms max. 20 ms max. 20 ms max. backlash 1 1 1 1 rating continuous continuous continuous continuous insulation grade ty p e f ty p e f ty p e f ty p e f
for complete specifications and additional models: u.s. www.omron.com/oei canada www.omron.ca i-13 smartstep servos cylindrical servo motors without brakes cylindrical servo motors with brakes item r7m-a03030-s1 r7m-a05030-s1 r7m-a10030-s1 r7m-a20030-s1 r7m-a40030-s1 r7m-a75030-s1 rated output 30 w 50 w 100 w 200 w 400 w 750 w rated torque 0.095 nm 0.159 nm 0.318 nm 0.637 nm 1.27 nm 2.39 nm rated rotation speed 3,000 r/min. 3,000 r/min. 3,000 r/min. 3,000 r/min. 3,000 r/min. 3,000 r/min. momentary maximum rotation speed 4,500 r/min. 4,500 r/min. 4,500 r/min. 4,500 r/min. 4,500 r/min. 4,500 r/min. momentary maximum torque 0.29 nm 0.48 nm 0.96 nm 1.91 nm 3.82 nm 7.1 nm rated current (rms) 0.42 a 0.6 a 0.87 a 2.0 a 2.6 a 4.4 a momentary maximum current (rms) 1.3 a 1.9 a 2.8 a 6.0 a 8.0 a 13.9 a rotor inertia 1.7 10 -6 kgm 2 2.2 10 -6 kgm 2 3.6 10 -6 kgm 2 1.19 10 -5 kgm 2 1.87 10 -5 kgm 2 6.67 10 -5 kgm 2 power rate 5.31 kw/s 11.5 kw/s 28.1 kw/s 34.1 kw/s 86.3 kw/s 85.6 kw/s allowable radial load 68 n 68 n 78 n 245 n 245 n 392 n allowable thrust load 54 n 54 n 54 n 74 n 74 n 147 n weight without brake 0.3 kg 0.4 kg 0.5 kg 1.1 kg 1.7 kg 3.4 kg applicable servo driver r7d-apa3h r7d-apa5h r7d-ap01h r7d-ap02h r7d-ap04h r7d-ap08h encoder resolution 2,000 pulses/revolution for phase-a and phase-b, 1 pulse/revolution for phase-z radiation shield dimensions t6 250 mm square item r7m-a0303-bs1 r7m-a05030- bs1 r7m-a10030- bs1 r7m-a20030- bs1 r7m-a40030- bs1 r7m-a75030- bs1 rated output 30 w 50 w 100 w 200 w 400 w 750 w rated torque 0.095 nm 0.159 nm 0.318 nm 0.637 nm 1.27 nm 2.39 nm rated rotation speed 3,000 r/min. 3,000 r/min. 3,000 r/min. 3,000 r/min. 3,000 r/min. 3,000 r/min. momentary maximum rotation speed 4,500 r/min. 4,500 r/min. 4,500 r/min. 4,500 r/min. 4,500 r/min. 4,500 r/min. momentary maximum torque 0.29 nm 0.48 nm 0.96 nm 1.91 nm 3.82 nm 7.1 nm rated current (rms) 0.42 a 0.6 a 0.87 a 2.0 a 2.6 a 4.4 a momentary maximum current (rms) 1.3 a 1.9 a 2.8 a 6.0 a 8.0 a 13.9 a rotor inertia 1.7 10 -6 kgm 2 2.2 10 -6 kgm 2 3.6 10 -6 kgm 2 1.19 10 -5 kgm 2 1.87 10 -5 kgm 2 6.67 10 -5 kgm 2 power rate 5.31 kw/s 11.5 kw/s 28.1 kw/s 34.1 kw/s 86.3 kw/s 85.6 kw/s allowable radial load 68 n 68 n 78 n 245 n 245 n 392 n allowable thrust load 54 n 54 n 54 n 74 n 74 n 147 n weight with brake 0.6 kg 0.7 kg 0.8 kg 1.6 kg 2.2 kg 4.3 kg applicable servo driver r7d-apa3h r7d-apa5h r7d-ap01h r7d-ap02h r7d-ap04h r7d-ap08h encoder resolution 2,000 pulses/revolution for phase-a and phase-b, 1 pulse/revolution for phase-z radiation shield dimensions t6 250 mm square brake specifica- tions brake inertia 0.85 10 -6 kgm 2 0.85 10 -6 kgm 2 0.85 10 -6 kgm 2 6.4 10 -6 kgm 2 6.4 10 -6 kgm 2 1.7 10 -5 kgm 2 excitation voltage 24 v dc 10% v power consumption (at 20 c) 6 w 6 w 6 w 7 w 7 w 7.7 w current consumption (at 20 c) 0.25 a 0.25 a 0.25 a 0.29 a 0.29 a 0.32 a static friction torque 0.2 nm min. 0.2 nm min. 0.34 nm min. 1.47 nm min. 1.47 nm min. 2.45 nm min. attraction time 30 ms max. 30 ms max. 30 ms max. 60 ms max. 60 ms max. 60 ms max. release time 60 ms max. 60 ms max. 60 ms max. 20 ms max. 20 ms max. 20 ms max. backlash 1 1 1 1 1 1 rating continuous continuous continuous continuous continuous continuous insulation grade type f type f type f type f type f type f
i-14 for complete specifications and additional models: u.s. www.omron.com/oei canada www.omron.ca smartstep servos dimensions servo drives dimensions (mm) cylindrical servo motors (3,000 r/min) dimensions (mm) 200 vac: 30 w/50 w/100 w/200 w/400 w/750 w without brake: r7m-a03030-s1-d/a05030-s1-d/a10030-s1-d/a20030-s1-d/a40030-s1-d/a75030-s1-d with brake: r7m-a03030-bs1-d/a05030-bs1-d/a10030-bs1-d/a20030-bs1-d/a40030-bs1-d/a75030-bs1-d input voltage rating drive model h w d 1-phase, 100 vac and 200 vac 30 w r7d-apa3h/l 160 55 130 50 w r7d-apa5h/l 160 55 130 100 w r7d-ap01h/l 160 55 130 200 w r7d-ap02h/l 160 55 130 400 w r7d-ap04h/l 160 75 130 1-phase, 200 vac 750 w r7d-ap08h 160 90 180 model overall length flange surface axis end ll lr c d1 d2 f g z s qk b h t1 r7m-a03030-s1 69.5 25 40 46 30h7 2.5 5 two, 4.3 dia. 6h6 14 2 2 1.2 r7m-a03030-bs1 101 25 40 46 30h7 2.5 5 two, 4.3 dia. 6h6 14 2 2 1.2 r7m-a05030-s1 77 25 40 46 30h7 2.5 5 two, 4.3 dia. 6h6 14 2 2 1.2 r7m-a05030-bs1 108.5 25 40 46 30h7 2.5 5 two, 4.3 dia. 6h6 14 2 2 1.2 r7m-a10030-s1 94.5 25 40 46 30h7 2.5 5 two, 4.3 dia. 8h6 14 3 3 1.8 r7m-a10030-bs1 135 25 40 46 30h7 2.5 5 two, 4.3 dia. 8h6 14 3 3 1.8 r7m-a20030-s1 96.5 30 60 70 50h7 3 6 four, 5.5 dia. 14h6 20 5 5 3 r7m-a20030-bs1 136 30 60 70 50h7 3 6 four, 5.5 dia. 14h6 20 5 5 3 r7m-a40030-s1 124.5 30 60 70 50h7 3 6 four, 5.5 dia. 14h6 20 5 5 3 r7m-a40030-bs1 164 30 60 70 50h7 3 6 four, 5.5 dia. 14h6 20 5 5 3 r7m-a75030-s1 145 40 80 90 70h7 3 8 four, 7 dia. 16h6 30 5 5 3 r7m-a75030-bs1 189.5 40 80 90 70h7 3 8 four, 7 dia. 16h6 30 5 5 3 r7m-a @@@ 30(-s1) (without brake) *axis end dimensions r7m-a @@@ 30(-s1) (with brake)
for complete specifications and additional models: u.s. www.omron.com/oei canada www.omron.ca i-15 smartstep servos flat servo motors (3,000 r/min) dimensions (mm) 200 vac: 100 w/200 w/400 w/750 w without brake: r7m-ap10030-s1-d/ap20030-s1-d/ap40030-s1-d/ap75030-s1-d with brake: r7m-ap10030-bs1-d/ap200 30-bs1-d/ap40030-bs1-d/ap75030-bs1-d model overall length flange surface axis end ll lr c d1 d2 f g z s qk b h t1 r7m-ap10030-s1 62 25 60 70 50h7 2.5 6 5.5 dia. 8h6 14 3 3 1.8 r7m-ap10030-bs1 91 25 60 70 50h7 2.5 6 5.5 dia. 8h6 14 3 3 1.8 r7m-ap20030-s1 67 30 80 90 70h7 3 8 7 dia. 14h6 16 5 5 3 r7m-ap20030-bs1 98.5 30 80 90 70h7 3 8 7 dia. 14h6 16 5 5 3 r7m-ap40030-s1 87 30 80 90 70h7 3 8 7 dia. 14h6 16 5 5 3 r7m-ap40030-bs1 118.5 30 80 90 70h7 3 8 7 dia. 14h6 16 5 5 3 r7m-ap75030-s1 86.5 40 120 145 110h7 3.5 10 10 dia. 16h6 22 5 5 3 r7m-ap75030-bs1 120 40 120 145 110h7 3.5 10 10 dia. 16h6 22 5 5 3 r7m-ap @@@ 30(-s1) (without brake) r7m-ap @@@ 30(-s1) (with brake) *axis end dimensions
|
